AMST'05 Advanced Manufacturing Systems and Technology: Proceedings of the Seventh International ConferenceElso Kuljanic Manufacturing a product is not difficult, the difficulty consists in manufacturing a product of high quality, at a low cost and rapidly. Drastic technological advances are changing global markets very rapidly. In such conditions the ability to compete successfully must be based on innovative ideas and new products which has to be of high quality yet low in price. One way to achieve these objecti ves would be through massive investments in research of computer based technology and by applying the approaches presented in this book. The First International Conference on Advanced Manufacturing Systems and Technology AMST87 was held in Opatija (Croatia) in October 1987. The Second International Conference on Advanced Manufacturing Systems and Technology AMSV90 was held in Trento (Italy) in lune 1990. The Third, Fourth, Fifth and Sixth Conferences on Advanced Manufacturing Systems and Technology were all held in Udine (Italy) as follows: AMST93 in April 1993, AMST96 in September 1996, AMST99 in June 1999 and AMST02 in June 2002. |
From inside the book
Results 1-5 of 78
Page 43
... obtained the curled long chip in milling stainless steel , Figure 2 . The width of the workpiece was only 50 mm , and a carbide cutter was used . The chips were more than 500 mm long and welded on each cutting edge . They would brake ...
... obtained the curled long chip in milling stainless steel , Figure 2 . The width of the workpiece was only 50 mm , and a carbide cutter was used . The chips were more than 500 mm long and welded on each cutting edge . They would brake ...
Page 45
... obtained only in Cincinnati " . Merchant's discovery of the science - based predictive model in engineering of the machining process , based on Ernst's shear plane , opened a new era in chip formation , i.e. in machining . 4 COMPUTER ...
... obtained only in Cincinnati " . Merchant's discovery of the science - based predictive model in engineering of the machining process , based on Ernst's shear plane , opened a new era in chip formation , i.e. in machining . 4 COMPUTER ...
Page 46
... obtained for two different tools , Table 1 . TABLE 1. Tool flank wear land after 30 minutes turning steel C45 with ... obtain : | t | = 1,72 and to = 0,05 = 2,145 . We may conclude that the arithmetical means of the tool A and the tool B ...
... obtained for two different tools , Table 1 . TABLE 1. Tool flank wear land after 30 minutes turning steel C45 with ... obtain : | t | = 1,72 and to = 0,05 = 2,145 . We may conclude that the arithmetical means of the tool A and the tool B ...
Page 47
... obtained with the regression analysis T versus vc , and equations b ) are obtained with regres- sion analysis vc versus T. It can be seen that the Taylor exponent m = 0,108 ( T versus v¿ ) is ap - proximately 40 % greater than the m ...
... obtained with the regression analysis T versus vc , and equations b ) are obtained with regres- sion analysis vc versus T. It can be seen that the Taylor exponent m = 0,108 ( T versus v¿ ) is ap - proximately 40 % greater than the m ...
Page 52
... obtained by simulation were compared to the experimental test results . The differences between the obtained simulation results where from 50 % to 400 % . The simulation of high speed machining by applying a physics base modeling ...
... obtained by simulation were compared to the experimental test results . The differences between the obtained simulation results where from 50 % to 400 % . The simulation of high speed machining by applying a physics base modeling ...
Contents
1 | |
16 | |
41 | |
57 | |
Unconventional Cutting Technologies in Orthopaedic Surgery | 89 |
Machining Processes | 119 |
Optimization of Machining Process Using Evolutionary Algorithms | 135 |
Nimonic Valves Case | 143 |
Improving Process Planning through Sequencing the Operations | 337 |
LowCost Transformation of a Conventional Milling Machine into | 357 |
Optimized Hotwire Cutting Robotic System for Expandable Polystyrene Foam | 377 |
Analysis and Modelling of Laser Beam Melt Ablation | 399 |
Preliminary Analysis | 413 |
New Possibilities by Direct Laser Micro Sintering for Micro System Technology | 427 |
an Approach to Flash Design | 465 |
An AccurateOptimized Mesh for ThermoMechanical Analysis of Laser | 483 |
Investigation of Toolpath Interpolation Methods in the HighSpeed | 165 |
A Study of Factors that Affect the BuildUp Material Formation | 185 |
Empirical Modelling and Optimization of Precision Grinding | 203 |
Tool Wear and Surface Aspects when Turning Titanium and Aluminium Alloys | 221 |
Modelling and Simulation Creep Feed Grinding Process | 234 |
Machine Tools and Flexible Manufacturing Systems | 249 |
3D Location of Circular Features for Robotic Tasks | 267 |
A Mobile Robot Platform for Ferromagnetic Base Plates | 279 |
Constrained HInfinity Design of PID Controllers | 299 |
Design of a Product Configuration System by the ObjectOriented Approach | 317 |
Influence of Process Parameters for Thixotropic Alloys | 503 |
Investigation on Heat Transfer in the Investment Casting | 625 |
Coating Photoelasticity Applied to a Rapid Prototyping Model of a | 645 |
Quality Aspects in the Sector of Waste from Electrical and Electronical | 663 |
Quality Assurance | 683 |
A New FMEA Approach Based on Availability and Costs | 703 |
NonContact Volumetric Measurement for Spine Evaluation and Production | 725 |
Six Sigma the Methodology for Acheiving Total Buisness Excellence | 741 |
Analysis of the Dependance Between Manufacturing and Design Specification | 757 |
Other editions - View all
Common terms and phrases
Advanced Manufacturing Systems alloys analysis application approach characteristics chip CIRP CISM CISM Courses components cost Courses and Lectures cutting forces cutting speed cutting tool defined deformation design of experiments developed diameter dynamic effect Engineering equation evaluation experimental feed FIGURE friction friction stir welding function geometric grinding wheel heat implementation improve increase industrial Kuljanic laser layer linear m/min machine tool material matrix measured mechanical metal method methodology micro milling monitoring neural network obtained operations optimization output performance phase PID controllers possible pressure problem procedure production pultrusion reduce robot rotation roughness SCADA sensor simulation sintering Six Sigma specific Springer Wien structure surface Systems and Technology Table temperature thermal thermocouples tool holder tool path tool wear University of Udine variables welding Wien New York workpiece